flespi telematics hub supports cellocator protocol. The list of supported devices Cellocator CelloTrack Cellocator CelloTrack Nano Cellocator CelloTrack 10Y Cellocator CelloTrack Solar Cellocator Cello CAN iQ Cellocator Cello IQ Cellocator CR-200 Cellocator CR-300 Cellocator CR-400 Cellocator Cello-F Cellocator MiniTrack

cellocator protocol updated: Sub Data type 0x16 - Fleet End of Trip Report - is supported for message type 9.

Cellocator protocol updated: Parsing of odometer value has changed and now works as follows: if device is registered and has current value of Odometer Unit setting - odometer reading is converted to km and stored as vehicle.mileage parameter otherwise - odometer reading is registered as vehicle.odometer parameter with unit unspecified (the unit may be miles, kilometers or 100 meters, configured in the device) Odometer Unit setting is supported for CR-300 devices:

Cellocator protocol updated: MCGP protocol message type 11 parsing refactored. Besides other changes, the following parameters are renamed: sensor.temperature.1 is renamed to sensor.temperature sensor.humidity.1 is renamed to sensor.humidity This parameters are registered for Module 40 Measurement Readings . Both old and new parameters are registered now. Old parameters will be removed 31-jan-2020.

[Changelog] cellocator protocol

namo

The following modules are supported for Message Type 11 of Cellocator protocol:

Module 25: Trigger Event ID
Module 2: Variables Dump List

Applicable for Cellocator Cello CAN iQ.

These modules are sent as parts of the Cello-CANiQ Trigger event message. They identify the trigger Event ID and the Cello-CANiQ variables list attached to the event. The variable dump list is a programmable list of CAN variables selected when the user builds the CAN triggering. Please refer to “Cello-CANiQ Integration Manual” for more details.

baja

Module 41 Legacy (Type-0) Encapsulated Message module supported for Message Type 11 of Cellocator protocol.

baja

cellocator protocol updated:
Sub Data type 0x19 - 1-Wire sensors data - is supported for message type 9.

namo

Cellocator protocol updated: Sub Data type 0x0D Compressed Vector Change Report is added for Message Type 9.

namo

Cellocator protocol updated: MCGP protocol message type 11 parsing refactored.
Besides other changes, the following parameters are renamed:

sensor.temperature.1 is renamed to sensor.temperature
sensor.humidity.1 is renamed to sensor.humidity

This parameters are registered for Module 40 Measurement Readings.
Both old and new parameters are registered now. Old parameters will be removed 31-jan-2020.

namo

namo
Cellocator protocol updated: old parameters removed after renaming.

kial

Output state change setting is supported for CR-300 devices:

namo

Programming command (message type 1) added for cellocator protocol. It allows to configure the cellocator devices.

namo

Message type 7 is supported for Cellocator protocol: Logged Fragment of Forwarded Data from Serial Port to
Wireless Channel. Container fragment is registered as hex string in parameter payload.hex.

namo

Output state change setting is supported for Cello IQ and Cello CAN IQ devices:

namo

Cellocator protocol update is planned for tomorrow 2020-08-27, 12:00 UTC - parsing will be switched to new parsing engine. This is an internal process, no changes in devices' work are expected.

namo

namo
Cellocator protocol switch to the new parsing engine is postponed till the next Thursday, 3-Sep-2020 12:00 UTC.

namo

namo
Cellocator protocol is updated to new parsing engine

namo

Commands of Cellocator protocol are refactored. The following changes was introduced:

New command Generic Command - custom_message_type_0 is implemented.
This command is to be used instead of status, reset, track_time, engine_stop commands which will be removed in a week, 3-Sep-2020. Examples may be found here.

New command Modular Message Request - custom_message_type_9 is implemented.
This command is to be used instead of firmware, can, location commands which will be removed in a week, 3-Sep-2020. Examples may be found here.

New command Programming Command - custom_message_type_1 is implemented. This command is a replacement for prog_cmd command which will be removed in a week, 3-Sep-2020. Examples may be found here.

namo

namo
Cellocator protocol updated:
commands status, reset, track_time, engine_stop, firmware, can, location and prog_cmd are removed.

namo

New settings added for Cellocator CR-300 device: Request Position and Request Connect to Server, Actions tab:

namo

Cellocator protocol updated: added parsing of Message Type 11 > Module 28 > Events:

1 - Impact
16 - Free-fall

Parameter acceleration.rms is registered for these events: acceleration RMS value of (X²+Y²+Z²), where each of the axes is in 250µg units.

namo

namo
One more Module 28 event is supported for Message type 11 for cellocator protocol:

Event 15 MultiSense Door/Window Open/Close - flespi parameter door.open.status

namo

Cellocator protocol updated: added parsing of Message Type 11 > Module 28 > Events:

3 - Man Down - flespi parameter mandown.alarm.status=true is registered for this event
11 - Check-In
18 - Sudden Pressure Change - flespi parameter altitude.difference is registered for this event (value is in meters)
19 - Check-out by timeout event
20 - Check-out by user event
23 - MultiSense button pressed event - flespi parameter button.pressed.event=true

namo

namo
Cellocator protocol updated: added parsing of one more Message Type 11 > Module 28 event:

21 - No MultiSense received

Time elapsed from the last reception of sensor value is stored into flespi parameter sensor.reading.fix.age

namo

The list of supported devices for Cellocator protocol has been extended to include the following ones: