• baja

  • Post #5
  • Edited

Module 41 Legacy (Type-0) Encapsulated Message module supported for Message Type 11 of Cellocator protocol.

    • baja

    • Post #6

    cellocator protocol updated:
    Sub Data type 0x19 - 1-Wire sensors data - is supported for message type 9.

      a month later

      Cellocator protocol updated: Sub Data type 0x0D Compressed Vector Change Report is added for Message Type 9.

        Cellocator protocol updated: MCGP protocol message type 11 parsing refactored.
        Besides other changes, the following parameters are renamed:

        • sensor.temperature.1 is renamed to sensor.temperature
        • sensor.humidity.1 is renamed to sensor.humidity

        This parameters are registered for Module 40 Measurement Readings.
        Both old and new parameters are registered now. Old parameters will be removed 31-jan-2020.

        • namo replied to this.
          5 days later

          Output state change setting is supported for CR-300 devices:

            namo
            Cellocator protocol updated: old parameters removed after renaming.

                21 days later

                Programming command (message type 1) added for cellocator protocol. It allows to configure the cellocator devices.

                  21 days later

                  • namo

                  • Post #12
                  • Edited

                  Message type 7 is supported for Cellocator protocol: Logged Fragment of Forwarded Data from Serial Port to
                  Wireless Channel                  . Container fragment is registered as hex string in parameter payload.hex.

                    2 months later
                    4 months later

                    • namo

                    • Post #14

                    Cellocator protocol update is planned for tomorrow 2020-08-27, 12:00 UTC - parsing will be switched to new parsing engine. This is an internal process, no changes in devices' work are expected.

                      namo
                      Cellocator protocol switch to the new parsing engine is postponed till the next Thursday, 3-Sep-2020 12:00 UTC.

                      • namo replied to this.

                          Commands of Cellocator protocol are refactored. The following changes was introduced:

                          1. New command Generic Command - custom_message_type_0 is implemented.
                            This command is to be used instead of status, reset, track_time, engine_stop commands which will be removed in a week, 3-Sep-2020. Examples may be found here.

                          1. New command Modular Message Request - custom_message_type_9 is implemented.
                            This command is to be used instead of firmware, can, location commands which will be removed in a week, 3-Sep-2020. Examples may be found here.

                          1. New command Programming Command - custom_message_type_1 is implemented. This command is a replacement for prog_cmd command which will be removed in a week, 3-Sep-2020. Examples may be found here.

                            8 days later

                            • namo

                            • Post #17

                            namo
                            Cellocator protocol updated:
                            commands status, reset, track_time, engine_stop, firmware, can, location and prog_cmd are removed.

                                namo
                                Cellocator protocol is updated to new parsing engine

                                    5 months later
                                    a month later

                                    • namo

                                    • Post #20
                                    • Edited

                                    Cellocator protocol updated: added parsing of Message Type 11 > Module 28 > Events:

                                    • 1 - Impact
                                    • 16 - Free-fall

                                    Parameter acceleration.rms is registered for these events: acceleration RMS value of (X²+Y²+Z²), where each of the axes is in 250µg units.

                                      namo
                                      One more Module 28 event is supported for Message type 11 for cellocator protocol:

                                      • Event 15 MultiSense Door/Window Open/Close - flespi parameter door.open.status

                                        • namo

                                        • Post #22
                                        • Edited

                                        Cellocator protocol updated: added parsing of Message Type 11 > Module 28 > Events:

                                        • 3 - Man Down - flespi parameter mandown.alarm.status=true is registered for this event
                                        • 11 - Check-In
                                        • 18 - Sudden Pressure Change - flespi parameter altitude.difference is registered for this event (value is in meters)
                                        • 19 - Check-out by timeout event
                                        • 20 - Check-out by user event
                                        • 23 - MultiSense button pressed event - flespi parameter button.pressed.event=true

                                        namo
                                        Cellocator protocol updated: added parsing of one more Message Type 11 > Module 28 event:

                                        • 21 - No MultiSense received

                                        Time elapsed from the last reception of sensor value is stored into flespi parameter sensor.reading.fix.age