Omnicomm protocol is supported in flespi telematics hub. The following devices are supported Omnicomm Optim Omnicomm Profi Omnicomm Light

Omnicomm protocol is updated. The following parameters are added: tacho.driver.card.code - Group 2 General, field number 15 accelerometer.state - Group 2 General, field number 16 motorhours - Group 2 General, field number 17 gsm.signal.level - Group 2 General, field number 18 wifi.signal.level - Group 2 General, field number 19

This is to announce parameters renaming in omnicomm protocol: parameter motorhours is renamed to motorhours.counter indexed parameter fuel.level is renamed to fuel.sensor.value indexed parameter liquid.sensor.fuel.temperature is renamed to fuel.sensor.temperature Both old and new parameters are registered now. Old parameters will be removed 21-jan-2020.

Omnicomm protocol is updated: group 9/9 SafeDriving is supported. The following flespi parameters are registered: EventMask - safe.driving.bitmask : bit0 - speed, bit1 - rpm, bit2 - acceleration, bit3 - lateral acceleration, bit4 - braking, bit5 - vertical acceleration SpeedThreshold - speed.threshold , km/h RPMThreshold - rpm.threshold , rpm AccelDangThs[0] - accelleration.threshold , g AccelDangThs[1] - braking.threshold , g AccelDangThs[2] - lateral.accelleration.threshold , g ccelDangThs[3] - vertical.accelleration.threshold , g

Omnicomm protocol is updated: group 11 OBDDt_J1979 is supported. The following flespi parameters are registered: SID_0x01_PID_0x0D Vehicle Speed Sensor, km/h - can.vehicle.speed SID_0x01_PID_0x31 Distance travelled since DTCs cleared, km - can.dtc.cleared.mileage SID_0x01_PID_0x4E Engine Run Time since diagnostic trouble codes cleared, minutes - can.dtc.cleared.engine.time SID_0x01_PID_0x42 Control module voltage, V - can.control.module.voltage SID_0x01_PID_0x0C = 5 Engine RPM, rpm - can.engine.rpm SID_0x01_PID_0x2F Fuel Level Input, % - can.fuel.level SID_0x01_PID_0x5E Engine Fuel Rate, L/h - can.engine.fuel.rate SID_0x01_PID_0x5C Engine Oil Temperature, °C - can.engine.oil.temperature SID_0x01_PID_0x05 Engine Coolant Temperature, °C - can.engine.coolant.temperature SID_0x01_PID_0x01 Check Engine - can.monitor.status.bitmask Bits A0-A6: Number of confirmed emissions-related DTCs available for display - can.dtc.number Bit A7: Off or On, indicates if the CEL/MIL is on (or should be on) - can.mil.status SID_0x09_PID_0x02 = 11 VIN ТС - vehicle.vin SID_0x01_PID_0x5E_quantity of fuel rate values read from CAN and used to calculate mean engine fuel rate (see above SID_0x01_PID_0x5E) - can.engine.fuel.rate.count

Parameters renaming in Omnicomm protocol: the following parameters that come from Group 2: General parameters are renamed: parameter can.vehicle.speed is renamed into vehicle.speed parameter can.engine.rpm is renamed into engine.rpm parameter can.onboard.power.voltage is renamed into external.powersource.voltage The renaming aims to avoid ambiguity between the same parameters - can.vehicle.speed , can.engine.rpm - that come from Group 7: CAN J1939 Data and from Group 11: OBD J1979 data . For the sake of backward compatibility, both old and new parameters will be registered until 3-Dec-2021. 3-Dec-2021 old parameters will be removed.

Omnicomm protocol is updated: Group 9, subgroup 3 Extended CAN parameters is supported. The following flespi parameters are registered: SPN IDs - can.spn.id , can.spn.id.1 , can.spn.id.2 etc SPN Values - can.spn.value , can.spn.value.1 , can.spn.value.2 etc

[Changelog] omnicomm protocol

namo

Omnicomm protocol is supported in flespi telematics hub.

Omnicomm

The following devices are supported

namo

Omnicomm protocol is updated. The following parameters are added:

tacho.driver.card.code - Group 2 General, field number 15
accelerometer.state - Group 2 General, field number 16
motorhours - Group 2 General, field number 17
gsm.signal.level - Group 2 General, field number 18
wifi.signal.level - Group 2 General, field number 19

namo

This is to announce parameters renaming in omnicomm protocol:

parameter motorhours is renamed to motorhours.counter
indexed parameter fuel.level is renamed to fuel.sensor.value
indexed parameter liquid.sensor.fuel.temperature is renamed to fuel.sensor.temperature

Both old and new parameters are registered now. Old parameters will be removed 21-jan-2020.

namo

namo
Omnicomm protocol updated: old parameters removed.

namo

Group 7 CanDt_J1939 - CAN data - is supported for omnicomm protocol.

namo

Omnicomm protocol update is planned for Monday 2020-09-19, 12:00 UTC - parsing will be switched to new parsing engine. This is an internal process, no changes in devices' work are expected.

namo

namo
Omnicomm protocol is updated to new parsing engine.

namo

Omnicomm protocol is updated: group 9/9 SafeDriving is supported.
The following flespi parameters are registered:

EventMask - safe.driving.bitmask:
bit0 - speed, bit1 - rpm, bit2 - acceleration, bit3 - lateral acceleration, bit4 - braking, bit5 - vertical acceleration
SpeedThreshold - speed.threshold, km/h
RPMThreshold - rpm.threshold, rpm
AccelDangThs[0] - accelleration.threshold, g
AccelDangThs[1] - braking.threshold, g
AccelDangThs[2] - lateral.accelleration.threshold, g
ccelDangThs[3] - vertical.accelleration.threshold, g

namo

Omnicomm protocol is updated: group 11 OBDDt_J1979 is supported.
The following flespi parameters are registered:

SID_0x01_PID_0x0D Vehicle Speed Sensor, km/h - can.vehicle.speed
SID_0x01_PID_0x31 Distance travelled since DTCs cleared, km - can.dtc.cleared.mileage
SID_0x01_PID_0x4E Engine Run Time since diagnostic trouble codes cleared, minutes - can.dtc.cleared.engine.time
SID_0x01_PID_0x42 Control module voltage, V - can.control.module.voltage
SID_0x01_PID_0x0C = 5 Engine RPM, rpm - can.engine.rpm
SID_0x01_PID_0x2F Fuel Level Input, % - can.fuel.level
SID_0x01_PID_0x5E Engine Fuel Rate, L/h - can.engine.fuel.rate
SID_0x01_PID_0x5C Engine Oil Temperature, °C - can.engine.oil.temperature
SID_0x01_PID_0x05 Engine Coolant Temperature, °C - can.engine.coolant.temperature
SID_0x01_PID_0x01 Check Engine - can.monitor.status.bitmask
- Bits A0-A6: Number of confirmed emissions-related DTCs available for display - can.dtc.number
- Bit A7: Off or On, indicates if the CEL/MIL is on (or should be on) - can.mil.status
SID_0x09_PID_0x02 = 11 VIN ТС - vehicle.vin
SID_0x01_PID_0x5E_quantity of fuel rate values read from CAN and used to calculate mean engine fuel rate (see above SID_0x01_PID_0x5E) - can.engine.fuel.rate.count

namo

Parameters renaming in Omnicomm protocol: the following parameters that come from Group 2: General parameters are renamed:

parameter can.vehicle.speed is renamed into vehicle.speed
parameter can.engine.rpm is renamed into engine.rpm
parameter can.onboard.power.voltage is renamed into external.powersource.voltage

The renaming aims to avoid ambiguity between the same parameters - can.vehicle.speed, can.engine.rpm - that come from Group 7: CAN J1939 Data and from Group 11: OBD J1979 data.

For the sake of backward compatibility, both old and new parameters will be registered until 3-Dec-2021.
3-Dec-2021 old parameters will be removed.

namo

Omnicomm protocol is updated: Group 9, subgroup 3 Extended CAN parameters is supported.
The following flespi parameters are registered:

SPN IDs - can.spn.id, can.spn.id.1, can.spn.id.2 etc
SPN Values - can.spn.value, can.spn.value.1, can.spn.value.2 etc