This is a changelog topic for suntech protocol. The list of supported devices Suntech ST600V Suntech ST600R Suntech ST630 Suntech ST640 Suntech ST640LC Suntech ST650 Suntech ST940 Suntech ST310U Suntech ST330 Suntech ST340 Suntech ST340LC(4pin) Suntech ST340R Suntech ST340UR Suntech ST300 Suntech ST300A Suntech ST300R Suntech ST300B Suntech ST300V Suntech ST300C Suntech ST300K Suntech ST300P Suntech ST300F Suntech ST300D Suntech ST300H Suntech ST400 Suntech ST410 Suntech ST500 Suntech ST3340 Suntech ST3340LC Suntech ST3940 Suntech ST3940B Suntech ST4290 Suntech ST4300 Suntech ST4310 Suntech ST4330 Suntech ST4340 Suntech ST3300 Suntech ST3310 Suntech ST3330 Suntech ST3330A Suntech ST4500 Suntech ST4910 Suntech ST4345R

Two Suntech devices added: ST3940 and ST3940B

Suntech protocol updated: 1. ST600R : MSR command reply parsing fixed 2. ST310U : ALT packet parsing fixed

Suntech protocol updated: ST310U : gsm.lac and gsm.bsic parameters parsing fixed ST410 : ALT report parsing fixed

New settings added for Suntech ST600V , ST600R , ST630 , ST640 , ST640LC devices. Actions tab: Request Status and Reboot Input/Output tab: Enable/Disable Output 1 , Output 2 and Output 4

New settings Odometer and Hour Meter are added on Actions tab Applicable for the following devices Suntech ST600V Suntech ST600R Suntech ST640 Suntech ST640LC Suntech ST630 Suntech ST310U Suntech ST340 Suntech ST340LC(4pin) Suntech ST340R Suntech ST300 Suntech ST300A Suntech ST300R Suntech ST300B Suntech ST300V Suntech ST300C Suntech ST300K Suntech ST300P Suntech ST300F Suntech ST300D Suntech ST300H

Suntech ST300R : fixed parsing of GSM CELL field

Assigned headers are supported for suntech protocol. Applicable for the devices that work over universal protocol , e.g. Suntech St4340

Suntech ST3940 and Suntech ST3940B : fixed parsing of PWR_VOLT field for Status, Emergency and Alert reports. Now this field's value is stored into parameter battery.level

[Changelog] suntech protocol

omol

Suntech protocol has been updated: new parameter timestamp.key is stored when device message contains Message Number field (registered as event.seqnum parameter is flespi). The parameter is used to distinguish between two messages with the same timestamp of seconds granularity.

omol

Suntech protocol has been updated: fixed STT, ALT and EVT reports parsing from ST340R.

omol

Suntech protocol has been updated: added new serial_port command to send any data to an external accessory (DEX command in documentation) for universal protocol devices.

omol

Suntech protocol has been updated: serial_port command (DEX as in documentation) is now supported by ST3xx devices (e.g. ST300, ST310U, ST340R, etc).

omol

Suntech protocol has been updated: fixed length field formatting in serial_port (DEX) command for universal protocol devices.

YuryAheichyk

Suntech protocol updated, added parsing of the following Medium Assigned Headers of Suntech universal protocol:

0x16 HDOP - flespi parameter position.hdop
0x17 VDOP - flespi parameter position.vdop

YuryAheichyk

Suntech protocol updated, added parsing of the SW_VER field Suntech universal protocol.

EvgenyShatilo

Universal protocol parsing updated. Added new following packets:

SNB: Basic Sensor Report
SNE: Extended Sensor Report (with BLE data)

omol

Suntech protocol has been updated: fixed bug in ASSIGN_MAP (Assigned Headers Map) field processing in STT and ALT reports from universal protocol devices.

omol

Suntech protocol has been updated: fixed bug in re-fetching STT/ALT Assigned Headers settings value.

YuryAheichyk

Suntech protocol has been updated, added Medium Assigned Headers: ST32T_RS485_FUEL1 - 4, Large Assigned Headers: ODOMETER, TOTAL_USED_FUEL, IDLE_FUEL, TOTAL_ENG_HR, ENGINE_IDLE_TIME, TRIP_FUEL, ENGINE_LOAD, FUEL LEVEL

baja

New device type added - Suntech ST4345R