This is a changelog topic for suntech protocol. The list of supported devices Suntech ST600V Suntech ST600R Suntech ST630 Suntech ST640 Suntech ST640LC Suntech ST650 Suntech ST940 Suntech ST310U Suntech ST310UC2 Suntech ST330 Suntech ST340 Suntech ST340LC(4pin) Suntech ST340R Suntech ST340UR Suntech ST300 Suntech ST300A Suntech ST300R Suntech ST300B Suntech ST300V Suntech ST300C Suntech ST300K Suntech ST300P Suntech ST300F Suntech ST300D Suntech ST300H Suntech ST400 Suntech ST410 Suntech ST500 Suntech ST3340 Suntech ST3340LC Suntech ST8300V Suntech ST8310 Suntech ST3940 Suntech ST3940B Suntech ST4290 Suntech ST4300 Suntech ST4310 Suntech ST4330 Suntech ST4340 Suntech ST3300 Suntech ST3310 Suntech ST3330 Suntech ST3330A Suntech ST4500 Suntech ST4910 Suntech ST4345R

Two Suntech devices added: ST3940 and ST3940B

Suntech protocol updated: 1. ST600R : MSR command reply parsing fixed 2. ST310U : ALT packet parsing fixed

Suntech protocol updated: ST310U : gsm.lac and gsm.bsic parameters parsing fixed ST410 : ALT report parsing fixed

New settings added for Suntech ST600V , ST600R , ST630 , ST640 , ST640LC devices. Actions tab: Request Status and Reboot Input/Output tab: Enable/Disable Output 1 , Output 2 and Output 4

New settings Odometer and Hour Meter are added on Actions tab Applicable for the following devices Suntech ST600V Suntech ST600R Suntech ST640 Suntech ST640LC Suntech ST630 Suntech ST310U Suntech ST340 Suntech ST340LC(4pin) Suntech ST340R Suntech ST300 Suntech ST300A Suntech ST300R Suntech ST300B Suntech ST300V Suntech ST300C Suntech ST300K Suntech ST300P Suntech ST300F Suntech ST300D Suntech ST300H

Suntech ST300R : fixed parsing of GSM CELL field

Assigned headers are supported for suntech protocol. Applicable for the devices that work over universal protocol , e.g. Suntech St4340

Suntech ST3940 and Suntech ST3940B : fixed parsing of PWR_VOLT field for Status, Emergency and Alert reports. Now this field's value is stored into parameter battery.level

[Changelog] suntech protocol

baja

Device ST4330 added
ST300 family PID report type integrated. New indexed parameter: obd.pid

namo

baja
Suntech protocol updated: added mapping of OBD PIDs for PID report into the named flespi parameters:
01 - can.monitor.status
03 - can.fuel.system.state.1 and can.fuel.system.state.2
04 - can.engine.load.level
05 - can.engine.coolant.temperature
06 - can.short.fuel.trim.1
07 - can.long.fuel.trim.1
08 - can.short.fuel.trim.2
09 - can.long.fuel.trim.2
0A - can.fuel.pressure
0B - can.intake.map
0C - can.engine.rpm
0D - can.vehicle.speed
0E - can.timing.advance
0F - can.intake.air.temperature
10 - can.maf.air.flow.rate
11 - can.throttle.position.1
12 - can.secondary.air.state
13 - can.oxygen.sensors.state
14 - can.oxygen.sensor.output.voltage.1 and can.oxygen.sensor.fuel.trim.1
15 - can.oxygen.sensor.output.voltage.2 and can.oxygen.sensor.fuel.trim.2
16 - can.oxygen.sensor.output.voltage.3 and can.oxygen.sensor.fuel.trim.3
17 - can.oxygen.sensor.output.voltage.4 and can.oxygen.sensor.fuel.trim.4
18 - can.oxygen.sensor.output.voltage.5 and can.oxygen.sensor.fuel.trim.5
19 - can.oxygen.sensor.output.voltage.6 and can.oxygen.sensor.fuel.trim.6
1A - can.oxygen.sensor.output.voltage.7 and can.oxygen.sensor.fuel.trim.7
1B - can.oxygen.sensor.output.voltage.8 and can.oxygen.sensor.fuel.trim.8
1C - obd.standard.enum
1F - can.engine.run.time
21 - can.mil.mileage
22 - can.relative.fuel.rail.pressure
23 - can.direct.fuel.rail.pressure
24 - can.oxygen.sensor.fuel.air.ratio.1 and can.oxygen.sensor.voltage.1
25 - can.oxygen.sensor.fuel.air.ratio.2 and can.oxygen.sensor.voltage.2
26 - can.oxygen.sensor.fuel.air.ratio.3 and can.oxygen.sensor.voltage.3
27 - can.oxygen.sensor.fuel.air.ratio.4 and can.oxygen.sensor.voltage.4
28 - can.oxygen.sensor.fuel.air.ratio.5 and can.oxygen.sensor.voltage.5
29 - can.oxygen.sensor.fuel.air.ratio.6 and can.oxygen.sensor.voltage.6
2A - can.oxygen.sensor.fuel.air.ratio.7 and can.oxygen.sensor.voltage.7
2B - can.oxygen.sensor.fuel.air.ratio.8 and can.oxygen.sensor.voltage.8
2C - can.commanded.egr
2D - can.egr.error
2E - can.evaporative.purge
2F - can.fuel.level
30 - can.dtc.cleared.warmups
31 - can.dtc.cleared.mileage
32 - can.evap.vapor.pressure
33 - can.barometric.pressure
34 - can.oxygen.sensor.fuel.air.ratio.1 and can.oxygen.sensor.current.1
35 - can.oxygen.sensor.fuel.air.ratio.2 and can.oxygen.sensor.current.2
36 - can.oxygen.sensor.fuel.air.ratio.3 and can.oxygen.sensor.current.3
37 - can.oxygen.sensor.fuel.air.ratio.4 and can.oxygen.sensor.current.4
38 - can.oxygen.sensor.fuel.air.ratio.5 and can.oxygen.sensor.current.5
39 - can.oxygen.sensor.fuel.air.ratio.6 and can.oxygen.sensor.current.6
3A - can.oxygen.sensor.fuel.air.ratio.7 and can.oxygen.sensor.current.7
3B - can.oxygen.sensor.fuel.air.ratio.8 and can.oxygen.sensor.current.8
3C - can.catalyst.temperature.1
3D - can.catalyst.temperature.2
3E - can.catalyst.temperature.3
3F - can.catalyst.temperature.4
41 - can.monitor.status
42 - can.control.module.voltage
43 - can.absolute.load
44 - can.equivalence.ratio
45 - can.relative.throttle.position
46 - can.ambient.air.temperature
47 - can.throttle.position.2
48 - can.throttle.position.3
49 - can.accelerator.pedal.position.1
4A - can.accelerator.pedal.position.2
4C - can.throttle.actuator
4D - can.mil.time
4E - can.dtc.cleared.engine.time
4F - can.oxygen.sensor.max.fuel.air.ratio, can.oxygen.sensor.max.voltage, can.oxygen.sensor.max.current and can.oxygen.sensor.max.pressure
50 - can.maf.max.air.flow.rate
51 - can.fuel.type.enum
52 - alcohol.fuel.percentage
55 - can.secondary.short.fuel.trim.1 and can.secondary.short.fuel.trim.3
56 - can.secondary.long.fuel.trim.1 and can.secondary.long.fuel.trim.3
57 - can.secondary.short.fuel.trim.2 and can.secondary.short.fuel.trim.4
58 - can.secondary.long.fuel.trim.2 and can.secondary.long.fuel.trim.4

namo

Suntech protocol is updated.
Parsing of Assigned headers for status STT and alert ALT reports now is based on the device configuration settings STT Assigned Headers and ALT Assigned Headers (see namo)

This is applicable for the following devices that work over Suntech universal protocol:
ST3300, ST3340, ST3940, ST3940B, ST4300, ST4310, ST4330, ST4340, ST4500, ST4910, ST4950

namo

Suntech protocol updated, added parsing of the following Small Assigned Headers of Suntech universal protocol:

0x0B ACC_X Acceleration X-Axis value - flespi parameter x.acceleration
0x0C ACC_Y Acceleration Y-Axis value - flespi parameter y.acceleration
0x0D ACC_Z Acceleration Z-Axis value - flespi parameter z.acceleration
0x0E ST25T_ADC_1 - flespi parameter ain.1
0x0F ST25T_ADC_2 - flespi parameter ain.2
0x10 ST25T_INPUT - flespi parameter din
0x11 ENGINE_TEMPERATURE - flespi parameter can.engine.coolant.temperature
0x12 OIL_PRESSURE - flespi parameter can.engine.oil.pressure
0x13 ALTITUDE (meter) - flespi parameter position.altitude
0x14 NET_STATUS Network Status - flespi parameter network.state
0x17 VEH_PROT Vehicle Prototype - flespi parameter vehicle.can.standard. Possible values: 0 - unknown, 1 - J1939, 2 - J1708, 3 - ISO15765

namo

New device type added Suntech ST3340LC

namo

New device type added Suntech ST650

namo

New device type added Suntech ST4910

baja

The STT_RPT_TYPE field of Universal protocol is stored as report.reason parameter

namo

PID report is supported for Universal Suntech protocol. Applicable for Suntech ST4500.
Mapping of the protocol fields into flespi parameters is the following:

MSG_TYPE (1 - real time, 0 - from storage) - message.buffered.status, boolean
DATE, TIME - timestamp
PID_DATA - obd.pid.1, obd.pid.2 etc, string

baja

New device types added Suntech ST3330 and Suntech ST3330A

baja

New device type added Suntech ST4950

namo

New device type added Suntech ST3310

namo

Suntech is updated: added SMS transport for the following settings:

Enable/disable output 1, Input/Output tab
Enable/disable output 2, Input/Output tab
Enable/disable output 4, Input/Output tab
Request status of the device, Actions tab
Reboot device, Actions tab

Note: to be able to send SMS to flespi devices - don't forget to specify phone number in the device configuration (on EDIT tab of the device)

baja

The protocol will be affected by the change in type of parameters gsm.mcc and gsm.mnc to be installed in 2 weeks - May 23rd, 2022: both parameters that now have type "string" will be stored as "number". The possible leading zeroes in MNC will be ignored (e.g. the value "01" will be stored as 1).

namo

Suntech protocol updated: timing parameters (ST410TIM) configuration command's response is supported for Suntech ST410.

namo

Suntech protocol is updated: parsing of short answer (without EXTRA_INFO field) for Enable/Disable commands is fixed.

namo

Suntech protocol is updated: reply for the Circular geofencing parameters command is supported. The update is applicable for Suntech ST600 series devices.

namo

Suntech protocol is updated: parsing of ALT alert report for geofence events is fixed. The update is applicable for Suntech ST600 series devices.

namo

Suntech protocol is updated:

added new device type Suntech ST340UR
parsing of STT, ALT, EMG and EVT reports of ST300 and ST600 series of devices is refactored

namo

Suntech protocol is updated.

Added setting Additional Parameters (Tracking tab) for Suntech ST340UR
Parsing of additional fields for ST300ALT report is based on the Report Additional Fields value of the Additional Parameters setting. If the value of the setting is unknown, then additional fields are skipped.