[Changelog] arnavi protocol

namo

We integrated arnavi protocol.

Arnavi arusnavi

Supported devices are:

Currently the protocol is implemented at basic level: only gps position, inputs, lbs, mileage and some other parameters are parsed. If you are interested in deeper protocol integration, please contact us in flespi chat.

namo

Arnavi protocol updated:

new parameters added:
- tags 10-17 IMPS_0 - IMPS_7 are registered as counter.impulses.1 - counter.impulses.8
- tags 20-27 FREQ_0 - FREQ_7 are registered as frequency.counter.din.1 - frequency.counter.din.8
- tags 30-37 VOLT_0 - VOLT_7 are registered as ain.1 - ain.8
bug fixed:
- tag 9 Device status, bits 24-31 external voltage - parameter external.powersource.voltage in flespi - was mistakenly multiplyed by 10. Now it's parsed correctly.

namo

Arnavi protocol updated: added tags 50 - 79. Mapping to flespi parameters is below:

tag 50 can_log_number - can.log.number
tag 51 can_security_state - registered bitwise:
- bit0 - bit2 - car.remote.control.state
- bit6 - can.module.sleep.mode
- bit8 - can.driver.door.status
- bit9 - can.passenger.door.status
- bit10 - can.trunk.status
- bit11 - can.hood.status
- bit12 - can.handbrake.status
- bit13 - can.pedal.brake.status
- bit14 - can.engine.status
- bit15 - can.webasto.status
- bit16 - can.engine.ignition.status
- bit17 - factory.alarm.actuated.status
- bit18 - can.car.closed.remote.status
- bit19 - can.ignition.key.status
- bit20 - can.dynamic.ignition.status
- bit21 - can.rear.left.door.status
- bit22 - can.rear.right.door.status
tag 52 CAN - total engine operating time (hours) - can.engine.motorhours
tag 53 CAN - full run TC (km) - can.vehicle.mileage
tag 54 CAN - full fuel consumption (l) - can.fuel.consumed
tag 55 CAN - the fuel level in the tank (%) - can.fuel.level
tag 56 CAN - the fuel level in the tank (l) - can.fuel.volume
tag 57 CAN - engine speed (rpm) - can.engine.rpm
tag 58 CAN - engine temperature (C) - can.engine.temperature
tag 59 CAN - Vehicle speed (km / h) - can.vehicle.speed
tag 60 CAN - the pressure on the axle 1 (kg) - can.axle.weight.1
tag 61 CAN - the pressure on the axle 2 (kg) - can.axle.weight.2
tag 62 CAN - the pressure on the axle 3 (kg) - can.axle.weight.3
tag 63 CAN - the pressure on the axle 4 (kg) - can.axle.weight.4
tag 64 CAN - the pressure on the axle 5 (kg) - can.axle.weight.5
tag 65 CAN - can_accident flags - registered bitwise:
- bit6 - can.passenger.seatbelt.indicator.status
- bit7 - can.driver.seatbelt.indicator.status
- bit8 - can.esp.indicator.status
- bit9 - can.glow.plug.indicator.status
- bit10 - can.soot.filter.indicator.status
- bit11 - can.electronic.power.control.status
- bit12 - can.parking.lights.status
- bit13 - can.low.beam.status
- bit14 - can.high.beam.status
- bit16 - can.check.engine.indicator.status
- bit17 - can.lights.failure.indicator.status
- bit18 - can.tire.pressure.low.status
- bit19 - can.wear.brake.pads.indicator.status
- bit20 - can.warning.indicator.status
- bit21 - can.abs.failure.indicator.status
- bit22 - can.fuel.level.low.indicator.status
- bit24 - can.stop.indicator.status
- bit25 - can.oil.pressure.indicator.status
- bit26 - can.coolant.level.low.indicator.status
- bit27 - can.handbrake.indicator.status
- bit28 - can.battery.indicator.status
- bit29 - can.airbag.indicator.status
tag 66 CAN - Status Flags agricultural equipment - can.agro.equipment.bitmask
tag 67 CAN - The fluid level AdBLUE (%) - can.adblue.level
tag 68 CAN - The fluid level AdBLUE (L) - can.adblue.volume
tag 69 CAN - driving_state:
- byte1 - can.throttle.pedal.level
- byte2 - can.engine.load.level
- byte3&4 - can.movement.state.bitmask
tag 70 LLS_0:
- byte1&2 - lls.value.1
- byte3 - lls.temperature.1
- byte4 - ble.asset.battery.voltage.1
  ...
tag 79 LLS_9:
- byte1&2 - lls.value.10
- byte3 - lls.temperature.10
- byte4 - ble.asset.battery.voltage.10

baja

The protocol will be affected by the change in type of parameters gsm.mcc and gsm.mnc to be installed in 2 weeks - May 23rd, 2022: both parameters that now have type "string" will be stored as "number". The possible leading zeroes in MNC will be ignored (e.g. the value "01" will be stored as 1).

namo

Arnavi protocol is updated: the following parameters are renamed:

can.driver.door.status is renamed to can.front.left.door.status
can.passenger.door.status is renamed to can.front.right.door.status

For backward compatibility both old and new parameters will be registered for 1 more week. Old parameters can.driver.door.status and can.passenger.door.status will be removed 01-Nov-2022.
Please, switch your applications to the new names of parameters until then.

namo

Arnavi protocol is updated - removed old parameters after renaming, see namo

EvgenyShatilo

Parsing of the packet "CONFIRM_THE_COMMAND2" with index 0x09 is added.

YuryAheichyk

Added 0x25 (WIFI) protocol version