We in flespi have supported morey protocol. This topic is a changelog for this protocol. The list of supported devices: Morey MC-4 Morey MC-4+ Morey MC-5

Morey protocol updated, the following EIDs added: 0x083 Internal Battery Type - flespi parameter battery.type 0x12B System Power State - flespi parameter system.power.state 0x3EA MC-4x Main App Version - flespi parameter device.firmware.version

Morey protocol is updated, the following EIDs are added: 0x088 .. 0x097 Custom Vehicle Bus Data Items 9 (0x088) to 24 (0x097) - flespi parameters can.32bit.value.9 - can.32bit.value.24 0x0B5 .. 0x0BC Custom Vehicle Bus Data Items 25 (0x0B5) to 32 (0x0BC) - flespi parameters can.32bit.value.25 - can.32bit.value.32 0x0BD Key Switch State - flespi parameter key.switch.state 0x0DF Verified Vehicle Bus Type - flespi parameter vehicle.bus.type

Morey protocol is updated, the following EIDs are added: 0x05F J1939 DTC - flespi parameter can.j1939.dtc 0x0DE Active DTC Count - flespi parameter can.dtc.number

Morey protocol is updated, the following EID is added: 0x07D Number of Tow Events - flespi parameter towing.events.count

Morey protocol is updated, the following EIDs are added: 0x039 System Wake Count - flespi parameter system.wake.count 0x03A System Uptime - flespi parameter system.uptime , sec 0x042 Motion Start Count - flespi parameter motion.start.count 0x043 Motion Stop Count - flespi parameter motion.stop.count 0x044 GPS Fail Count - flespi parameter gnss.fail.count 0x046 Modem Connect Retry Count - flespi parameter modem.connect.retry.count 0x047 Modem Comm Fail Count - flespi parameter modem.comm.fail.count 0x048 Modem Comm Retry Count - flespi parameter modem.comm.retry.count 0x053 Number of Transitions to Engine Running - flespi parameter engine.turn.on.count 0x055 Number of Transitions to Engine Not Running - flespi parameter engine.turn.off.count 0x056 Engine Not Running Time - flespi parameter engine.not.running.time , sec 0x057 Resets Since Power Up - flespi parameter resets.count 0x05C GPS State - flespi parameter gnss.state.enum 0x05D Modem State - flespi parameter modem.state.enum 0x069 Hard Braking Count - flespi parameter harsh.braking.number 0x06A Hard Acceleration Count - flespi parameter harsh.acceleration.number 0x06B Engine Running Trip Duration - flespi parameter trip.duration , sec 0x06C Engine Running Trip Estimated Odometer - flespi parameter trip.mileage , km 0x0BF Jolt Count - flespi parameter jolt.count 0x0C0 RPM-Based Engine On Counts - flespi parameter engine.turn.on.rpm.count 0x0C1 Voltage-Based Engine On Counts - flespi parameter engine.turn.on.voltage.count 0x09D Last Motion Sense Method - flespi parameter motion.sensor.type 0x09E .. 0x0A0 Overspeed 1-3 Duration - flespi parameter overspeeding.duration.1 - overspeeding.duration.3 0x0A1 Max Speed, cm/sec - flespi parameter segment.max.speed , km/h 0x0A2 Last Hard Braking Deceleration Rate, cm/sec2 - flespi parameter segment.max.braking.acceleration , g 0x0A3 Last Hard Acceleration Rate, cm/sec2 - flespi parameter segment.max.acceleration , g

Morey protocol is updated. The following EIDs are supported: 0x03F Modem Active Count - flespi parameter modem.power.on.count 0x040 Modem Uptime - flespi parameter modem.uptime , seconds 0x045 Modem Connect Fail Count - flespi parameter modem.connect.fail.count 0x058 UDP Bytes Received - flespi parameter udp.bytes.received 0x059 UDP Bytes Sent - flespi parameter udp.bytes.sent 0x05A UDP Packets Received - flespi parameter udp.packets.received 0x05B UDP Packets Sent - flespi parameter udp.packets.sent 0x0B4 Cellular Comm Backoff Indicator - flespi parameter gsm.backoff.status , boolean 0x0DC Unsolicited UDP Requests - flespi parameter udp.requests.unsolicited

Morey protocol is updated. The following EID is added: 0x146 UDS Based DTC indicator - flespi parameters can.uds.dtc , can.uds.dtc.1 , can.uds.dtc.2 etc

Morey protocol is updated. The following EIDs are added: 0x140 WABCO TSCII ABS Active Signal - flespi parameter can.wabco.abs.gio.active.signal 0x141 WABCO TSCII Speed Signal ISS1 - flespi parameter can.wabco.abs.gio.speed.signal.1 0x142 WABCO TSCII Speed Signal ISS2 - flespi parameter can.wabco.abs.gio.speed.signal.2 0x143 WABCO TSCII Meritor Tire Inflation System (MTIS) Status - flespi parameter can.wabco.abs.gio.mtis.state 0x144 WABCO TSCII FN MOD REQ FCF1 - flespi parameter can.wabco.abs.gio.mod.req.1 0x145 WABCO TSCII FN MOD REQ FCF2 - flespi parameter can.wabco.abs.gio.mod.req.2

Morey protocol is updated. The following EIDs are added: 0x03C GPS Active Count - flespi parameter gnss.power.on.count 0x03D GPS Uptime - flespi parameter gnss.power.on.duration, seconds 0x07E Turn Count - flespi parameter turn.events.count 0x080 SIM CCID - flespi parameter gsm.sim.iccid, string

Bugfix. Though the timestamp in Morey protocol is integer it caused merging of the messages with the same timestamp on the device storage level. New parameter timestamp.key added which is timestamp + report.seqnum * 0.00001 . This parameter is used as secondary key in device messages database, thus messages with the same timestamp but different report.seqnum won't be merged.

[Changelog] morey protocol

namo

Morey protocol is updated: fixed parsing of message type 0x0D BLE Advertisement

shal

Added message parameters sources annotation on the protocol page.

shal

Morey protocol is updated:

added EID 0x026 Instantaneous Fuel Economy - flespi parameter can.fuel.economy;
added EID 0x024 Engine Crankcase Pressure - flespi parameter can.engine.crankcase.pressure;

shal

Morey protocol is updated: all CAN parameters with unreadable values (0xFF, 0xFFFF, 0xFFFFFFFF) are removed from message. Parameter fuel.consumed renamed to can.fuel.consumed.

kial

Morey protocol is updated: Added parsing for EIDs 0x3EB ... 0x3EE with Log Entry Data Elements

kial

Morey protocol is updated: Added parsing for EIDs 0x0D0 ... 0x0DB and 0x0CC ... 0x0CF with parameters script.uint32.variable.5 ... script.uint32.variable.16 and script.int32.variable.5 ... script.int32.variable.8

kial

Breaking change of the morey protocol scheduled for the next Thursday, October 19.
Due to an implementation bug the position.speed parameter contains speed value in cm/sec, but that standard parameter should be in km/h. That will be fixed next Thursday, October 19.

Currently we have added a temporary parameter named "ref.position.speed.kmph" containing vehicle speed in km/h units. That parameter will be deleted with the bug fix on the next Thursday, October 19.

Please concat us if you need more time to prepare for this change, or if you need help with plugin creation that can convert speed parameter units.

kial

position.speed parameter units changed from cm/sec to km/h as mentioned in kial

baja

Indexed parameter can.j1708.dtc.{index} parsed from ID 0x05E from renamed to can.obd.dtc.{index}

YuryAheichyk

Fixed log.transaction.flags.name parameter parsing from 0x3ED EID

baja

parameter renaming announcement which will happen in a week (May 22):
parameter total.idle.seconds will be renamed to total.idle.time