This topic will be used to post changes in galileosky protocol implementation The list of supported devices Galileosky Base Block Optimum Galileosky Base Block Wi-Fi Galileosky Base Block Wi-Fi Hub Galileosky Base Block Lite Galileosky Base Block 3G Galileosky Boxfinder v 1.0 Galileosky OBD-II Galileosky v 1.9 Galileosky v 2.5 Galileosky v 4.0 Galileosky v 5.0 Galileosky v 5.1 Galileosky 7.0 Lite Galileosky 7.0 Galileosky 7.0 Wi-Fi Galileosky 7x Galileosky 7x C Galileosky 7x 3G Galileosky 7x Plus Galileosky 7x LTE Galileosky 10 Galileosky 10 C Galileosky 10 Hub Galileosky 10 Plus Galileosky 10 Pro

Settings added for OBD-II device type (obd_2, device_type_id=509) network_sim0, network_sim1, backend_server, backend_server2, wr_period, tracking, easylogic_get, easylogic_set, easylogic_clear, headpack1, mainpack1, canbus, shock

Galileosky protocol is updated: parameter external.powersource.voltage.range.outside.status is renamed to external.powersource.voltage.status Both old and new parameters are registered now. Old parameter will be removed 17-feb-2020.

Galileosky switched to a new parsing engine. Parsing and out-coming traffic had been checked on a real device before migration.

get_script channel level command (used to get EasyLogic scripts installed on device) will be removed in a week on Friday August 07. Custom command with payload "SCRIPT" can be used instead. Reason: protocol was moved to new parsing engine, though we try to avoid using commands without parameters.

get_script channel level command removed

Several new devices are added for Galileosky protocol: Galileosky 7x Galileosky 7x C Galileosky 7x 3G Galileosky 7x Plus Galileosky 7x LTE

Galileosky protocol is updated: added support for extended tags 0xFE . The following mapping takes place for Galileosky extended tag and flespi parameter : 0x01 Tag Modbus 0 ... 0x20 Tag Modbus 31 - modbus.sensor.value.0 - modbus.sensor.value.31 0x21 Tag Bluetooth 0 ... 0x60 Tag Bluetooth 63 - blutooth.sensor.value.0 - blutooth.sensor.value.63 0x61 Tag Modbus 32... 0x80 Tag Modbus 63 - modbus.sensor.value.32 - modbus.sensor.value.63 0x81 Cell identifier (CID) - gsm.cellid 0x82 Local area code (LAC) - gsm.lac 0x83 Country code (MCC) - gsm.mcc 0x84 Operator code (MNC) - gsm.mnc 0x85 RSSI - gsm.signal.dbm Applicable for Galileosky 7x series: Galileosky 7x , Galileosky 7x C , Galileosky 7x 3G , Galileosky 7x Plus , Galileosky 7x LTE

Galileosky protocol updated, parameters tyre.sensor.connection.status tyre.sensor.battery.low.status tyre.sensor.reason.enum are renamed to tire.sensor.connection.status tire.sensor.battery.low.status tire.sensor.reason.enum Old parameters will be registered until 05-Jan-2022 together with the new ones. Old parameters will be removed 05-Jan-2022.

The protocol will be affected by the change in type of parameters gsm.mcc and gsm.mnc to be installed in 2 weeks - May 23rd, 2022: both parameters that now have type "string" will be stored as "number". The possible leading zeroes in MNC will be ignored (e.g. the value "01" will be stored as 1).

[Changelog] galileosky protocol

EvgenyShatilo

Fixed registration of extended tag 0xFE parameters.
All 4-byte parameters must be signed by default. Previously they were unsigned.

Concerns parameters modbus.sensor.value, bluetooth.sensor.value.

YuryAheichyk

Added Main packet with compression parsing

YuryAheichyk

Added 0xAE BLE MAC extended tag parsing

baja

Extended tags parsing added:
Tag ID 0x291C stored to can.gear
Tag IDs 0x29CD-0x29DC and 0x3610-0x366F: Auxiliary I/O sensors 1-112 stored to can.auxiliary.io.sensor.1 to can.auxiliary.io.sensor.112
Tag ID 0x3803 stored to can.scr.feedback.control.state

shal

New parameter can.engine.fan.speed.1 added for v10 devices (J1939 SPN 111 - Engine Fan 1 Speed).

bird

Fixed SPN tag 0x277F (SPN 111): parameter corrected from can.engine.fan.speed to can.engine.coolant.level

Fixed SPN tag 0x2809 (SPN 249): data type corrected from double to int64, parameter corrected from can.vehicle.mileage to can.engine.revolutions

New SPN tags supported in extended tags block (0xFE):

0x291F (SPN 527) — can.cruise.control.state
0x2963 (SPN 595) — can.cruise.status
0x2966 (SPN 598) — can.pedal.clutch.status
0x2CD8 (SPN 1480) — can.retarder.selection
0x2D5C (SPN 1612) — can.driver.work.state.enum
0x2D5E (SPN 1614) — can.tacho.overspeeding.event
0x2D5F (SPN 1615) — can.driver.card.status
0x2D61 (SPN 1617) — can.driver.time.related.status
0x2D63 (SPN 1619) — can.tacho.reverse.movement.status
0x2D67 (SPN 1623) — can.tacho.position.speed (output shaft speed)
0x2D68 (SPN 1624) — can.tacho.position.speed (vehicle speed)
0x2D69 (SPN 1625) — tacho.driver.card.code (driver identification)

bird

10 new CAN SPN parameters supported in extended tags:

can.driver.demand.engine.torque (SPN 512)
can.actual.engine.torque (SPN 513)
can.nominal.friction.torque (SPN 514)
can.brake.pedal.level (SPN 521)
can.accelerator.pedal.low.idle.switch.state (SPN 558)
can.accelerator.pedal.kickdown.switch.state (SPN 559)
can.engine.oil.level (SPN 98)
can.transmission.input.speed (SPN 161)
can.fuel.economy (SPN 184)
can.trip.mileage (SPN 918)

bird

26 new J1939 SPN tags supported in extended tags block (0xFE) for v10/v10_hub devices, including engine torque, fuel economy, brake pedal, cruise control, transmission, service distance, PTO, tachograph, and more.

New parameters:

can.washer.fluid.level — washer fluid level from CAN bus
can.engine.torque.available.maximum — actual maximum available engine percent torque

Unknown SPN tags no longer terminate device connections — unsupported tags generate a warning and parsing continues with the rest of the message.

bird

Graceful degradation extended to 0x95-0xA3 and 0xB7-0xD8 extended tag ranges — devices sending these tags will no longer disconnect.

bird

New extended tags supported for v10_hub devices with WiFi module: 0xA4 (Modem WiFi Status), 0xA5 (WiFi Error Code), 0xAD (WiFi MAC Address), 0xB3 (Collector Archive Status).
New parameters: wifi.module.status.enum, wifi.error.enum, device.wifi.mac.address, archive.records.count, archive.records.sent.count.

bird

89 new J1939 SPN extended tag parameters added for v10_hub devices — engine, fuel, aftertreatment/DPF/SCR, pressure/temperature sensors, and other CAN bus parameters.

bird

New parameter can.egr.valve.position added for SPN 27 (Engine Exhaust Gas Recirculation 1 Valve Position)

bird

New parameters added:

can.dpf.inlet.pressure for SPN 81 (Aftertreatment 1 Diesel Particulate Filter Intake Pressure)
can.cruise.control.low.set.limit.speed for SPN 88 (Cruise Control Operator Low Set Limit Speed)
can.total.engine.idle.time for SPN 235 (Engine Total Idle Hours)
can.inverter.rate.limits.crc for SPN 12026 (Motor/Generator 4 Inverter Rate Limits Active 1 CRC)
can.nox.mass.bin for SPN 12538 (NOx Tracking Valid NOx Lifetime System Out NOx Mass Bin 14)
can.hvesp.module.operational.status for SPN 15779 (HVESP14 Module 17 Operational Status)

bird

New parameters added:

can.engine.oil.filter.differential.pressure for SPN 99 (Engine Oil Filter Differential Pressure)
can.intake.manifold.pressure for SPN 102 (Engine Intake Manifold 1 Pressure)
can.idle.fuel.consumed for SPN 236 (Engine Total Idle Fuel Used)
can.parking.trailer.air.pressure for SPN 1086 (Parking and/or Trailer Air Pressure)

bird

New parameter can.alternator.current for SPN 115 (Alternator Current)

YuryAheichyk

added parsing of extended SPN tags 0x2954-0x295D (SPN 580-589): altitude, transmission gear ratio, axle weight, pitch, latitude, longitude, make, model, serial number, alternator speed

YuryAheichyk

Added SPN 120 Hydraulic Retarder Oil Temperature (tag 0x2788) as can.retarder.oil.temperature; SPN values following this tag in a packet are no longer lost.

EvgenyShatilo

Tachograph live activity parameters standardization

To make tachograph data consistent across all flespi protocols, we introduced unified tachograph driver parameters (per card slot, .1 / .2), reported from the CAN tachograph SPN tags:

tacho.driver.card.code - driver card id inserted into the tachograph slot
tacho.driver.activity.state.enum - current activity: 0 - rest, 1 - work, 2 - drive, 3 - available, 4 - not available, 5 - error
tacho.driver.activity.state - the same as text: rest / work / drive / available / not available / error

The following parameters are deprecated and will be removed on 01.11.2026:

can.driver.work.state.enum -> tacho.driver.activity.state.enum.1 (attention: enum values differ from the old ones)
can.driver.2.work.state.enum -> tacho.driver.activity.state.enum.2 (attention: enum values differ from the old ones)
tacho.driver.card.code indexed by CAN source address (e.g. tacho.driver.card.code.239) -> tacho.driver.card.code.1

Please update your expressions, calculators, plugins and streams before the removal date.

bird

New parameter can.pto.governor.enable.switch added for Galileosky devices