Meitrack protocol is supported in flespi telematics hub. The list of supported devices Meitrack MD500S Meitrack MD511H Meitrack MD522S Meitrack MD533S Meitrack MD811H Meitrack MD822S Meitrack MT90 Meitrack MT90G Meitrack MVT100 Meitrack MVT340 Meitrack MVT380 Meitrack MVT400 Meitrack MVT600 Meitrack MVT800 Meitrack P88L Meitrack P99G Meitrack T1 Meitrack T3 Meitrack T32 Meitrack T311 Meitrack T322X Meitrack T333 Meitrack T355 Meitrack T366 Meitrack T366G Meitrack T399L Meitrack T622 Meitrack T633L Meitrack TC68S Meitrack T399 Y41 Meitrack T711L Meitrack TC68SL Meitrack TC68L Meitrack TS299L Meitrack MD600 Meitrack MD833H Meitrack MD300

Meitrack protocol updated: CCE command type is supported. This is applicable for P99G , TC68S and other devices.

CCC command type is supported for meitrack protocol. This is applicacle for Meitrack T322X device type.

Time Zone setting added for the following devices, Actions tab: Devices Meitrack MT90 Meitrack MVT100 Meitrack MVT340 Meitrack MVT380 Meitrack MVT600 Meitrack MVT800 Meitrack T1 Meitrack T32 Meitrack T311 Meitrack T322X Meitrack T333 Meitrack TC68S

Parameter ID 0x40 New event code is supported for CCE command type. Applicable for Meitrack TC68S

E91 command type is supported for meitrack protocol: read device's firmware version and serial number. Applicable for the following devices Meitrack MT90 Meitrack MT90G Meitrack MVT100 Meitrack MVT340 Meitrack MVT380 Meitrack MVT600 Meitrack MVT800 Meitrack P99G Meitrack T1 Meitrack T3 Meitrack T32 Meitrack T311 Meitrack T322X Meitrack T333 Meitrack T355 Meitrack T366 Meitrack T366G Meitrack T622 Meitrack TC68S Firmware version and serial number are stored in Device Information setting, Info tab:

New parameters IDs are supported for CCE command type: 0x92 - can.wheel.speed 0x99 - can.engine.rpm 0x9C - can.engine.coolant.temperature 0xC9 - can.fuel.consumption.distance Applicable for Meitrack TC68S

Parameter ID 0x4A is supported for CCE command type: additional info about the ignition off event. The information is registered in the following parameters: trip.mileage trip.duration trip.average.speed trip.max.speed Applicable for Meitrack TC68S

New device supported: Meitrack P88L

Meitrack protocol is updated: fixed parsing of wifi.signal.strength parameter.

The protocol will be affected by the change in type of parameters gsm.mcc and gsm.mnc to be installed in 2 weeks - May 23rd, 2022: both parameters that now have type "string" will be stored as "number". The possible leading zeroes in MNC will be ignored (e.g. the value "01" will be stored as 1)

[Changelog] meitrack protocol

baja

CCE ID 0x68 parsing to x.tilt.angle, y.tilt.angle and z.tilt.angle added

Correct command response parsing for the command CC7 added

baja

Custom command updated: additional check for command_type parameter added: it can not be longer than 3 characters.

baja

Report type 110 data representing Transparent CAN data is now stored as payload.hex message parameter.

YuryAheichyk

Added new device Meitrack T399 Y41

YuryAheichyk

Added new device Meitrack T711L

YuryAheichyk

Added new devices:

YuryAheichyk

Added new devices:

YuryAheichyk

Added new device:

Meitrack MD300

namo

Meitrack protocol is updated: parsing of Wifi MAC addresses is refactored.

shal

New event code mappings added for multiple Meitrack device families:

T711L: Event codes now map to engine.ignition.status, movement.status, sleep.mode.status, overspeeding.event, harsh.cornering.event, harsh.braking.event, harsh.acceleration.event, crash.event, ibutton.connected.status, idle.event, fatigue.driving.status
TC68L: Event codes now map to geofence.status, towing.event, power.on.status, engine.ignition.status, movement.status, harsh.braking.event, harsh.acceleration.event, idle.event, fatigue.driving.status
TC68SL/TS299L: Event codes now map to geofence.status, towing.event, power.on.status
T322X/MVT100/MVT340: Event codes now map to engine.ignition.status, movement.status, sleep.mode.status, overspeeding.event, harsh.cornering.event, geofence.status, towing.event, power.on.status
MVT600/T1/T333/T32/T633L: Same mappings as T322X family
MVT380/MVT800: Same mappings as T322X family

shal

Comprehensive event code parsing update for meitrack protocol:

T711L: Complete coverage (53 codes) including door, inputs, geofence, temperature, fuel, security, outputs, BLE, maintenance
TC68L: Added SOS, speeding, sleep, RPM, engine temperature, speed recovery, maintenance
T322X/MVT600/MVT380: Added SOS, door, inputs, GSM jamming, temperature, fuel, security, fall/install/drop, maintenance
T633L: Added SOS, door, inputs 4-9, temperature, fuel, speed recovery

shal

T633L: Added event codes for impact detection (78) and sharp turns (90/91)